1.  

    Ahmet ARAN - Seçilmiş Yayınlar

                                                                                                                                                                ANASAYFA

    1. A.Aran, "Dövme Endüstrisinde Kalite Kontrol Uygulamaları", Mühendis ve Makina, 22 (l978) 26.

    2. A.Aran, "An Experimental Comparison of Different Methods to Determine the Strain Rate Sensitivity Index of Superplastic Materials", Scripta Met., 13 (1979) 843.

    3. A.Aran and M.Demirkol, "Effect of Heat Treatment on the Bauschinger Effect for a Carbon Steel", Mater.Sci.Eng. 47 (1981) 89.

    4. M.Gevrek,M.Demirkol and A.Aran, "An Investigation of the Validity of Different Load Calculation Methods in Hot Rolling", Proc. 3rd National Metallurgy Congress, Ankara, l979, p.619.

    5. A.Aran and D.E.Gücer, "High Temperature Torsional Low- Cycle Fatigue of OFHC Copper", Z.Metallkde., 72 (1981) 476.

    6. A.Aran, "Effect of the Heat Treatment on the Stress-Strain Behaviour of Dual Phase Steels in Forward and Reverse Straining", Z.Metallkde., 73 (1982) 667.

    7. M.Demirkol ve A.Aran, "Düşük Karbonlu Yapı Çeliklerini Çift Fazlı İçyapı Oluşturarak Kullanma Olanakları", 1.Ulusal Makina Tasarım ve İmalat Kongresi, Ankara 1984, Bildiriler Kitabı s. 531.

    8. A.Aran ve A.Taygur, "Pi 70/30 Pirinç Malzemede Biçimlendirme Sınırı Eğrilerinin Mekanik Özellikler Yardımıyla Teorik Olarak Saptanması ve Tane Büyüklüğünün Etkisi", 8. Metalurji Sempozyumu, İstanbul 1984.

    9. A.Karabulut ve A.Aran, "2024 Aluminyum Alaşımında Soğutma Hızı Duyarlığı", 2. Alüminyum Sanayi Kongresi, Seydişehir 1984, Bildiriler Kitabı s.363.

    10. M.Demirkol ve A.Aran, "Yük Vagonu Dingillerinin Yorulma ve Kırılma Mekaniği Açısından İncelenmesi", 2. Ulusal Kırılma Kongresi, Trabzon 1987, Bildiriler Kitabı s.197.

    11. S.Onurlu ve A.Aran, "Şekil Değişimi Hızına Duyarlı Malzemelerin Konik Kalıpla Endirek Ekstrüzyonunda Kuvvet Hesabı, 4. Ulusal Metalurji Kongresi, Ankara 1986, Bildiriler Kitabı, s.632.

    12. M.Afacan ve A.Aran, "Dairesel Delik İçeren Elyaf Takviyeli Karma Malzeme Levhalara Uygulanan Gerilme Kırılması Kriterleri", 2.Ulusal Kırılma Kongresi, Trabzon 1987, Bildiriler Kitabı,s.109.

    13. A.Aran, M.Demirkol and A.Karabulut, "Bauschinger Effect in Precipitation Strengthened 2024 Aluminium Alloy", Mater.Sci.Eng. 89 (1987) L35.

    14. Ş.Yılmaz ve A.Aran, "Karma Malzemelerde Sulu Ortam Etkisiyle Özelliklerin Değişimi",3. Ulusal Makina Tasarım ve İmalat Kongresi,Ankara 1988, Bildiriler Kitabı, s.549.

    15. A.Aran and M.Afacan, "Karbon Elyaf Takviyeli Karma (Kompozit) Malzemeler",  Mühendis ve Makina, 29 (1988) 21.

    16. A.Aran, "Optimization of the Strength and Intergranular Corrosion Properties of the 7075 Alloy by Retrogression and Reaging", Z.Metallkde. 80 (1989)

    17. A.Aran, "Makina Parçalarının Tasarım ve İmalatında Artık Gerilmelerin Önemi", Mühendis ve Makina, 30 (1989) 5.29

    18. A.Aran, "CAD/CAM Applications in Closed Die Forging", 4th National Machine Theory Congress, Yalova 1990, p.99.

    19. A.Aran and H.Türker, "The Effect of Martensite Content on the Fatigue Behaviour of a Ferritic-Martensitic Steel", J.Mater.Sci.Let. 9 (1990) 1407.

    20. M.Demirkol and A.Aran, "Cyclic Stress-Strain Behaviour of 2024 Aluminium Alloy", Z.Metallkde. 81 (1990) 887.

    21. A.Aran, "Tensile and Fatigue Properties of Carburizing Steels with Ferritic-Martensitic Microstructure", 1st Metallurgical Symposium, Ahwaz - Iran, 1991, Paper no.30.

    22. I.B.Eryürek, A.Aran and M.Çapa, "Fracture of a Coupling in a Line- shaft Vertical Turbine Pump", ASM Handbook of Case Histories in Failure Analysis, American Society for Metals, 1993, p.354.

    23. M.Sezer and A.Aran, "A Computer programme for the Calculation of the Elastic Properties for Multilayered Fibre-reinforced Composites", Proc. of the Ninth International Conference of Composite Materials, Vol.III, p.314, Madrid, 1993.

    24. A.Aran and Ş.Yılmaz, "A FEM Analysis of the Microplastic Flow in Particle Reinforced Metal Matrix Composites", Proc. of the 4th European Conference on Advanced Materials and Processes, p.165, Padua/Venice 1995. 

    25. Ş.Yılmaz and A.Aran, "Finite Element Analysis of Elastoplastic Behavior of SiC Particulate Reinforced Al Matrix, Bulletin of the Technical University of Istanbul, 48 (1995) 623.

    26. A.Cansun and A.Aran, "Thermal Residual Stresses and Their Effect on the Mechanical Properties in SiCp Reinforced Al Matrix Composites", Materials Science Forum, Vols.217-222 (1996) 1115.

    27. Ş.Yılmaz and A.Aran, "Finite Element Analysis of Deformation Behavior and Local Damages in Al Matrix-SiC Particulate Composite Microstructures", Materials Sci. Forum, Vols.217-222 (1996) 1121.

    28. A.Aran, "Metal Matrix Composites” (invited paper), Proc. of Mechanical Engineering Conference MAMKON, p.368, Istanbul 1997.

    29. A.Aran and Safak Yilmaz, "Microplasticity in MMC's", NATO ASI- Advanced Light Alloys and Composites, Zakopane, Poland, September 1997.

    30. Ş.Yılmaz and A.Aran , "Finite Element Analysis of Deformation Behavior in Ductile Matrix Containing Hard Particles", Materials Science and Technology, 14 (1998) 1154.

    31. Ş.Yılmaz and A.Aran , "Finite Element Analysis of the Effect of Particle Alignment on the Deformation Behavior for Ductile Matrix Containing Hard Particles", Canadian Metallurgical Quarterly 38 (1999) 201.

    32. M.Sezer and A.Aran, "Fatigue Behavior of Discontinuous Glass Fiber Reinforced Polypropylene", Plastics Failure Analysis and Prevention, (John Moalli, Editor) ChemTech Publishing, 2001.

    33. Temiz, A.Aran, “Quality Assurance and Accreditation in Higher Education”, invited paper V. National Mechanical Engineering Education Symposium, Istanbul, November 2003.

    34. A.Aran, “Accreditation and Recognition of Engineering Degrees and the Turkish Experience”, Proc. of the International Symposium NEW METHODS AND CURRICULA IN ENGINEERING EDUCATION IN A NEW EUROPE, p.298, Valladolid 2004.

    35.  A.Aran, “The Design Component in Engineering Curriculum” Proc. of the 3rd Balkan Region Conference on Engineering Education p.141, Sibiu 2005.

    36. A.Aran, “Emerging Educational Quality Assurance Approaches in Turkey”, invited paper, 2006 ABET Annual Meeting: The 3rd ABET International Congress on Education, Accreditation, and Practice - Tampa, FL.
      37.

    37. A.E. Payzın, A.Aran "International Developments in Accreditation of Engineering Education and the Case for Turkey" Proc. of 2007 ASEE GLOBAL COLLOQUIUM ON ENGINEERING EDUCATION, October 2007, Istanbul Turkey.

    Kitaplar

    1. Ş.Güleç ve A.Aran, "Çelik ve Dökme Demirlerin Yorulma Dayanımı (H.Tauscher'den çeviri), 210 sayfa, 175 Şekil, MAE Matbaası 1983.

    2. Ş.Güleç ve A.Aran, "Malzeme Bilgisi", (H-J. Bargel ve G.Schulze'den çeviri), 2.baskı, 190 sayfa, 252 Şekil, İ.T.Ü. Yayını, 1993.

    3. A.Aran, "Elyaf Takviyeli Karma Malzemeler", İ.T.Ü. Yayını, Sayı:1420, 95 sayfa, 33 şekil, 1990.

    4. A.Aran, "Metal Döküm Teknolojisi", 172 sayfa, 104 şekil, 2.baskı Birsen Yayını  Istanbul 1999.